Prosoft-technology 5201-MNET-101S Manuel d'utilisateur Page 48
- Page / 159
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
101S Protocol Configuration IEC-101 Slave ♦ ProLinx Communication Gateway
Protocol Manual IEC 60870-5-101 v3 Slave (Firmware version 3.xx)
Page 48 of 159 ProSoft Technology, Inc.
August 6, 2010
2.15 [C_SE_NA_1]
This section defines the normalized setpoint database. This information is
sourced from the remote Master and is transferred to the database.
You can associate a command with a monitored single-point database value to
coordinate the command/monitor operation. You must enter the correct M
ONITOR
POINT # and MONITOR DB ADDRESS values in the table. If the REQUIRE SELECT
parameter is not set to zero, a select command must be received before an
execute command will be processed.
This section takes the following parameters:
P
OINT #
DB
ADDRESS
M
ONITOR POINT #
M
ONITOR DB ADDRESS
R
EQUIRE SELECT
Each point consumes one word. The DB
ADDRESS value corresponds to the word
offset in the database.
The
DB ADDRESS should be located in a database area that is being constantly
moved from the Master to the gateway.
For additional information on how to set these parameters, see the Reference
chapter of this manual.
2.16 [C_SE_NB_1]
This section defines the scaled setpoint database. This information is sourced
from the remote Master and is transferred to the database.
You can associate a command with a monitored single-point database value to
coordinate the command/monitor operation. You must enter the correct M
ONITOR
POINT # and MONITOR DB ADDRESS values in the table. If the REQUIRE SELECT
parameter is not set to zero, a select command must be received before an
execute command will be processed.
This section takes the following parameters:
P
OINT #
DB
ADDRESS
M
ONITOR POINT #
M
ONITOR DB ADDRESS
R
EQUIRE SELECT
Each point consumes one word. The DB
ADDRESS value corresponds to the word
offset in the database.
The
DB ADDRESS should be located in a database area that is being constantly
moved from the Master to the gateway.
For additional information on how to set these parameters, see the Reference
chapter of this manual.
- IEC-101 Slave 1
- Your Feedback Please 2
- ProSoft Technology 2
- Product Documentation 2
- Markings 3
- Contents 5
- 1 Start Here 11
- 1.3.1 Using the Online Help 12
- 1.4.2 Renaming PCB Objects 15
- To Download the Project File 21
- 2.1 [IEC-870-5-101 Port 0] 24
- 2.1.1 Enabled 24
- 2.1.2 Time DB Offset 24
- ES or NO 25
- to 65535 25
- 2.1.15 Maximum ASDU Resp Len 27
- 2.1.17 Freeze Start Type 27
- 2.1.18 Interval for Freeze 29
- 2.1.19 Set Priority Queues 30
- 2.1.20 Event Priority 31
- 2.1.22 IV Check Delay Time 33
- 2.1.23 IV Fail Count 33
- 2.1.24 Event Scan Delay 33
- 2.1.25 Scan Events 34
- 2.1.26 Time Type 35
- 2.1.27 Use Balanced Mode 35
- 2.1.28 Retry Count 35
- milliseconds 36
- 2.1.35 Receive Timeout 37
- 2.1.36 Hardware Handshaking 37
- 2.2.1 Short Pulse Time 38
- 2.2.2 Long Pulse Time 38
- 2.2.3 Point Count 39
- 2.2.4 Sequence Flag 40
- 2.2.5 Parameter Offset 41
- 2.3 [M_SP_NA_1] 42
- 2.4 [M_DP_NA_1] 42
- 2.5 [M_ST_NA_1] 43
- 2.6 [M_BO_NA_1 104] 43
- 2.7 [M_ME_NA_1] 44
- 2.8 [M_ME_NB_1] 44
- 2.9 [M_ME_NC_1] 45
- 2.10 [M_IT_NA_1] 45
- 2.11 [C_SC_NA_1] 46
- 2.12 [C_DC_NA_1] 46
- 2.13 [C_RC_NA_1] 47
- 2.14 [C_BO_NA_1 104] 47
- 2.15 [C_SE_NA_1] 48
- 2.16 [C_SE_NB_1] 48
- 2.17 [C_SE_NC_1] 49
- 2.18 Group Codes 50
- 3.3.4 RS-422 55
- 3.3.6 RS-485 and RS-422 Tip 55
- 4.1 LED Indicators 57
- 4.1.1 Base Gateway LEDs 57
- to open the Main menu 60
- 4.2.2 Navigation 61
- 4.2.3 Keystrokes 61
- 5 Reference 63
- 5.1.3 Internal Database 64
- 5.2.4 Using Monitor Points 81
- 100 Bit 0 of word 100 94
- 101 Bit 1 of word 100 94
- 102 Bit 2 of word 100 94
- 400 Words 5 and 6 98
- 401 Words 6 and 7 98
- 402 Words 9 and 10 98
- 5.2.6 Events 99
- Example - Event Priority 109
- Statement 129
- 6.1 System or Device 130
- 6.2 Network Configuration 130
- 6.3 Physical Layer 130
- 6.6.6 File Transfer 134
- 6.8.3 Read Procedure 137
- 6.8.6 Station Interrogation 138
- 6.8.7 Clock Synchronization 138
- 6.8.8 Command Transmission 139
- 6.8.10 Parameter Loading 140
- 6.8.11 Parameter Activation 140
- 6.8.12 Test Procedure 140
- 6.8.13 File Transfer 140
- 6.8.14 Background Scan 141
- In This Chapter 143
- Address 146
- Require Select 146
- 7.4 C_RC_NA Form 147
- 8.2.1 All Product Returns: 150
- 8.3 LIMITED WARRANTY 152
- 8.3.8 No Other Warranties 155
- 8.3.9 Allocation of Risks 155
Produits connexes et manuels pour Relais Prosoft-technology 5201-MNET-101S
(235 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels